Addonics Technologies POCKET ULTRA DIGIDRIVE AEPUDDSA9 User Manual

T E C H N O L O G I E S  
User Guide  
Pocket Ultra DigiDrive  
(AEPUDDU / AEPUDDU9 / AEPUDDSA / AEPUDDSA9)  
v7.1.11  
Technical Support  
If you need any assistance to get your unit functioning properly, please have your  
product information ready and contact Addonics Technical Support at:  
Hours: 8:30 am - 6:00 pm PST  
Phone: 408-453-6212  
Driver Installation  
For Win98 and Win98SE  
Note:  
Plug and Play under Windows Me, 2000 and XP  
Uses Mass Storage Driver under Windows Me,  
Windows 2000 and XP (Plug and Play)  
1.  
2.  
3.  
4.  
5.  
Make sure your computer is up and running  
Verify that all cables are connected.  
Insert the Flash card that you will be using to the Digidrive.  
Connect the USB cable to the USB Port.  
A "New Hardware Found" message shall pops up.  
a.  
Follow the ON SCREEN wizard and point to the location of A:\USBWIN98 for the  
driver.  
b.  
c.  
Let Windows finish the installation and that’s it.  
Double click My Computer icon and see if you have an extra drive letter for the  
Pocket Ultra Digidrive.  
You may now access the Pocket Ultra Digidrive.  
Operation of Pocket UDD  
The pocket UDD is designed not to draw any power when there is no media inserted. So the LED light will  
remain off even the device is connected to the computer.  
Use the following procedures to add or remove the media from the Pocket UDD.  
1.  
Insert the media fully into the device, the LED light will turn green, indicating the media is  
properly inserted inside and the device is now turned on. Your operating system will report new  
hardware detected and begin to install the device. This may take a few seconds before a new  
drive icon appears in the My Computer folder. During this initialization, the LED light on the  
Pocket UDD toggles between orange and green color; and will stay green once the computer  
recognizes the media.  
2.  
Once the drive icon appears, the media is now ready and can be used like regular floppy  
media.  
3.  
4.  
During the read / write operation, the LED light of the Pocket UDD will turn Red.  
To remove the media, click on the Safe Remove icon to stop the connection as shown below.  
Once the “you may now safely remove window” shows up, you can then remove the media  
from the Pocket UDD by pushing on the eject button.  
Note: if you eject the media from the Pocket UDD without checking the Safe Remove icon, a  
warning message will appear from Windows 98SE, Me and 2000. This message is a reminder  
that it is safer to use the Safe Remove icon when you remove the media to prevent possible  
data loss in case you are in the middle of copying a file to and from the media. You can go  
ahead and close this message.  
5.  
6.  
After the media is ejected from the Pocket UDD, the LED light will go off, indicating the media  
is fully ejected from the device.  
Do not pull the media out of the device without using the eject button. This may crash the  
computer, as it does not realize the media has been manually removed from the device.  
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  
CONTACT US  
Phone:  
Fax:  
408-573-8580  
408-573-8588  
Email:  

Microsoft Windows 7 Home Premium With Service Pack QGF00154 User Manual
Kyocera QCP 6035 User Manual
Kenwood KDC W657 User Manual
JVC USB Connection Kit User Manual
HP Hewlett Packard 92500 User Manual
Hamilton Beach 43324 User Manual
Emerson HD7100 User Manual
Eclipse Fujitsu Ten avn5435 User Manual
Craftsman 247776360 User Manual
Aiwa XR M35 User Manual